| Basic unit SIMOCODE pro C, PROFIBUS DP interface 12 Mbit/s, RS 485, 4I/3O freely parameterizable, Us: 24 V DC, input for thermistor connection Monostable relay outputs |
| Product brand name | SIRIUS |
| Product designation | Motor management system |
| Design of the product | basic unit 1 |
| Product type designation | SIMOCODE pro C |
| General technical data |
| Product function | |
| Bus communication | Yes |
| data acquisition function | Yes |
| Diagnostics function | Yes |
| Password protection | Yes |
| Test function | Yes |
| maintenance function | Yes |
| Product component | |
| input for thermistor connection | Yes |
| Digital input | Yes |
| input for analog temperature sensors | No |
| input for ground fault detection | No |
| Relay output | Yes |
| Product extension | |
| Temperature monitoring module | No |
| Current measuring module | Yes |
| Current/voltage measuring module | No |
| failsafe digital I/O module | No |
| Ground fault monitoring module | No |
| Control unit with display | No |
| Control unit | Yes |
| analog I/O module | No |
| Consumed active power | 5 W |
| Insulation voltage | |
| with degree of pollution 3 rated value | 300 V |
| Surge voltage resistance rated value | 4 000 V |
| Protection class IP | IP20 |
| Shock resistance | |
| acc. to IEC 60068-2-27 | 15g / 11 ms |
| Vibration resistance | 1-6 Hz / 15 mm; 6-500 Hz / 2 g |
| Switching capacity current of the NO contacts of the relay outputs at AC-15 | |
| at 24 V | 6 A |
| at 120 V | 6 A |
| at 230 V | 3 A |
| Switching capacity current of the NO contacts of the relay outputs at DC-13 | |
| at 24 V | 2 A |
| at 60 V | 0.55 A |
| at 125 V | 0.25 A |
| Mechanical service life (switching cycles) | |
| typical | 10 000 000 |
| Electrical endurance (switching cycles) | |
| typical | 100 000 |
| Buffering time in the event of power failure | 0.05 s |
| Reference code acc. to DIN EN 81346-2 | F |
| Continuous current of the NO contacts of the relay outputs | |
| at 50 °C | 6 A |
| at 60 °C | 5 A |
| Type of input characteristic | Type 1 in accordance with EN 61131-2 |
| Electromagnetic compatibility |
| EMC emitted interference | |
| acc. to IEC 60947-1 | class A |
| EMI immunity acc. to IEC 60947-1 | corresponds to degree of severity 3 |
| Conducted interference | |
| due to burst acc. to IEC 61000-4-4 | 2 kV (power ports) / 1 kV (signal ports) |
| due to conductor-earth surge acc. to IEC 61000-4-5 | 2 kV |
| due to conductor-conductor surge acc. to IEC 61000-4-5 | 1 kV |
| due to high-frequency radiation acc. to IEC 61000-4-6 | 10 V |
| Field-bound parasitic coupling acc. to IEC 61000-4-3 | 10 V/m |
| Electrostatic discharge acc. to IEC 61000-4-2 | 6 kV contact discharge / 8 kV air discharge |
| Conducted HF-interference emissions acc. to CISPR11 | corresponds to degree of severity A |
| Field-bound HF-interference emission acc. to CISPR11 | corresponds to degree of severity A |
| Inputs/ Outputs |
| Product function | |
| Parameterizable inputs | Yes |
| Parameterizable outputs | Yes |
| Number of inputs | 4 |
| for thermistor connection | 1 |
| Number of digital inputs | |
| with a common reference potential | 4 |
| Digital input version | |
| Type 1 acc. to IEC 61131 | Yes |
| Input voltage at digital input at DC rated value | 24 V |
| Number of outputs | 3 |
| Number of semiconductor outputs | 0 |
| Number of outputs as contact-affected switching element | 3 |
| Switching behavior | monostable |
| Type of relay outputs | Monostable |
| Wire length for digital signals maximum | 300 m |
| Wire length for thermistor connection | |
| with conductor cross-section = 0.5 mm² maximum | 50 m |
| with conductor cross-section = 1.5 mm² maximum | 150 m |
| with conductor cross-section = 2.5 mm² maximum | 250 m |
| Protective and monitoring functions |
| Product function | |
| Phase unbalance | Yes |
| blocking current evaluation | Yes |
| power factor monitoring | No |
| Ground fault detection | Yes |
| Phase failure detection | Yes |
| phase sequence recognition | No |
| voltage detection | No |
| Monitoring of number of start operations | Yes |
| Overvoltage detection | No |
| Overcurrent detection 1 phase | Yes |
| undervoltage detection | No |
| undercurrent detection 1 phase | Yes |
| active power monitoring | No |
| Product function | |
| Current detection | Yes |
| Overload protection | Yes |
| Evaluation of thermistor motor protection | Yes |
| Total cold resistance number of sensors in series maximum | 1.5 kΩ |
| Response value of thermoresistor | 3 400 ... 3 800 Ω |
| of the short-circuit control | 9 Ω |
| Release value of thermoresistor | 1 500 ... 1 650 Ω |
| Explosion device group and category acc. to ATEX product directive 94/9/EC | Ex II (2) GD / Ex I (M2) |
| Motor control functions |
| Product function | |
| parameterizable overload relay | Yes |
| circuit breaker control | Yes |
| direct start | Yes |
| reverse starting | Yes |
| star-delta circuit | No |
| star-delta reversing circuit | No |
| Dahlander circuit | No |
| Dahlander reversing circuit | No |
| pole-changing switch circuit | No |
| pole-changing switch reversing circuit | No |
| Slide control | No |
| valve control | No |
| Communication/ Protocol |
| |
| Protocol is supported PROFIBUS DP protocol | Yes |
| Protocol is supported PROFINET IO protocol | No |
| Protocol is supported PROFIsafe protocol | No |
| Protocol is supported Modbus RTU | No |
| Protocol is supported EtherNet/IP | No |
| Protocol is supported OPC UA Server | No |
| Protocol is supported LLDP | No |
| Protocol is supported Address Resolution Protocol (ARP) | No |
| Protocol is supported SNMP | No |
| Protocol is supported HTTPS | No |
| Protocol is supported NTP | No |
| Protocol is supported Media Redundancy Protocol (MRP) | No |
| Product function is supported Device Level Ring (DLR) | No |
| Number of interfaces | |
| acc. to PROFINET | 0 |
| acc. to PROFIBUS | 1 |
| according to Ethernet/IP | 0 |
| Product function | |
| web server | No |
| shared device | No |
| at the Ethernet interface Autocrossover | No |
| at the Ethernet interface Autonegotiation | No |
| at the Ethernet interface Autosensing | No |
| is supported PROFINET system redundancy | No |
| supports PROFIenergy measured values | No |
| supports PROFIenergy shutdown | No |
| Transfer rate maximum | 12 Mbit/s |
| Identification & maintenance function | |
| I&M0 - device-specific information | Yes |
| I&M1 – higher-level designation/location designation | Yes |
| I&M2 - installation date | Yes |
| I&M3 - comment | Yes |
| Type of electrical connection | |
| of the communication interface | 9-pin SUB-D socket (12 Mbit) / screw terminal (1.5 Mbit) |
| Installation/ mounting/ dimensions |
| Mounting position | any |
| Mounting type | screw and snap-on mounting |
| Height | 111 mm |
| Width | 45 mm |
| Depth | 95 mm |
| Required spacing | |
| top | 40 mm |
| bottom | 40 mm |
| left | 0 mm |
| right | 0 mm |
| Connections/Terminals |
| Product function | |
| removable terminal for auxiliary and control circuit | Yes |
| Type of electrical connection | |
| for auxiliary and control current circuit | screw-type terminals |
| Type of connectable conductor cross-sections | |
| solid | 1x (0.5 ... 4.0 mm²), 2x (0.5 ... 2.5 mm²) |
| finely stranded with core end processing | 1x (0.5 ... 2.5 mm²), 2x (0.5 ... 1.5 mm²) |
| at AWG conductors solid | 1x (20 ... 12), 2x (20 ... 14) |
| at AWG conductors stranded | 1x (20 ... 14), 2x (20 ... 16) |
| Tightening torque | |
| with screw-type terminals | 0.8 ... 1.2 N·m |
| Tightening torque [lbf·in] | |
| with screw-type terminals | 7 ... 10.3 lbf·in |
| Type of connectable conductor cross-sections for PROFIBUS wire | 2x 0.34 mm², AWG 22 |
| Ambient conditions |
| Installation altitude at height above sea level | |
| 1 maximum | 2 000 m |
| 2 maximum | 3 000 m; max. +50 °C (no protective separation) |
| 3 maximum | 4 000 m; No protective separation at 40 °C |
| Ambient temperature | |
| during operation | -25 ... +60 °C |
| during storage | -40 ... +80 °C |
| during transport | -40 ... +80 °C |
| Environmental category | |
| during operation acc. to IEC 60721 | 3K6 (no formation of ice, no condensation, relative humidity 10 ... 95%), 3C3 (no salt mist), 3S2 (sand must not get into the devices), 3M6 |
| during storage acc. to IEC 60721 | 1K6 (no condensation, relative humidity 10 ... 95%), 1C2 (no salt mist), 1S2 (sand must not get into the devices), 1M4 |
| during transport acc. to IEC 60721 | 2K2, 2C1, 2S1, 2M2 |
| Relative humidity | |
| during operation | 5 ... 95 % |
| Contact rating of auxiliary contacts according to UL | B300 / R300 |
| Short-circuit protection |
| Design of short-circuit protection | |
| per output | Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-breaker C char.: 1.6 A (IEC 60947-5-1) or 6 A (I_K < 500 A) |
| Safety related data |
| Protection against electrical shock | finger-safe |
| Control circuit/ Control |
| Product function soft starter control | No |
| Type of voltage of the control supply voltage | DC |
| Control supply voltage 1 | |
| at DC rated value | 24 V |
| Operating range factor control supply voltage rated value at DC | |
| initial value | 0.8 |
| Full-scale value | 1.2 |
